扫一扫体验手机阅读
cisco 3560交换机和H3C S5120 链路聚合配置实例。
<span type="1" blog_id="1114641" userid='
340篇文章，62W+人气，15粉丝
高并发架构之路
￥51.00151人订阅
9本网络安全实战书籍精华
￥51.00514人订阅Cisco与H3C链路聚合对接_百度文库
您的浏览器Javascript被禁用，需开启后体验完整功能，
享专业文档下载特权
&赠共享文档下载特权
&100W篇文档免费专享
&每天抽奖多种福利
两大类热门资源免费畅读
续费一年阅读会员，立省24元！
Cisco与H3C链路聚合对接
你可能喜欢交换机链路聚合
& www.2cto.com &
SWA交换机配置内容： &www.2cto.com &
Switch&enable&
Switch#conf
Switch#configure&
Configuring from terminal, memory, or network [terminal]?&
Enter configuration commands, one per line. &End with CNTL/Z.
Switch(config)#h
Switch(config)#hostname SWA
SWA(config)#in vl
SWA(config)#in vlan 1
SWA(config-if)#ip add 192.168.1.101 255.255.255.0
SWA(config-if)#no shu
SWA(config-if)#no shutdown
%LINK-5-CHANGED: Interface Vlan1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
SWA(config-if)#ex
SWA(config)#sp
SWA(config)#spanning-tree m
SWA(config)#spanning-tree mode r
SWA(config)#spanning-tree mode rapid-pvst&
SWA(config)#in f0/1
SWA(config-if)#channel-g
SWA(config-if)#channel-group 1 m
SWA(config-if)#channel-group 1 mode d
SWA(config-if)#channel-group 1 mode desirable
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
SWA(config-if)#ex
SWA(config)#in f0/2
SWA(config-if)#channel-g
SWA(config-if)#channel-group 1 m
SWA(config-if)#channel-group 1 mode d
SWA(config-if)#channel-group 1 mode desirable
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up
SWA(config-if)#ex
SWA(config)#
SWB交换机配置内容： &www.2cto.com &
Switch&enable&
Switch#conf
Switch#configure&
Configuring from terminal, memory, or network [terminal]?&
Enter configuration commands, one per line. &End with CNTL/Z.
Switch(config)#h
Switch(config)#hostname SWB
SWB(config)#in vl
SWB(config)#in vlan 1
SWB(config-if)#ip add 192.168.1.102 255.255.255.0
SWB(config-if)#no shu
SWB(config-if)#no shutdown
%LINK-5-CHANGED: Interface Vlan1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
SWB(config-if)#ex
SWB(config)#sp
SWB(config)#spanning-tree m
SWB(config)#spanning-tree mode&
SWB(config)#spanning-tree mode r
SWB(config)#spanning-tree mode rapid-pvst&
SWB(config)#in f0/1
SWB(config-if)#channel-g
SWB(config-if)#channel-group 1 m
SWB(config-if)#channel-group 1 mode d
SWB(config-if)#channel-group 1 mode desirable
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
SWB(config-if)#
%LINK-5-CHANGED: Interface Port-channel 1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel 1, changed state to up
SWB(config-if)#ex
SWB(config)#in f0/2
SWB(config-if)#channel-g
SWB(config-if)#channel-group 1 m
SWB(config-if)#channel-group 1 mode d
SWB(config-if)#channel-group 1 mode desirable
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up
SWB(config-if)#ex
SWB(config)#已解决问题
【求助帖】&H3C交换机&堆叠后&如何跨设备链路聚合
提问时间： 12:47:03
浏览次数：1270
把S3900跨设备和 6509做链路聚合的配置 6509只支持静态和手工聚合，测试中以静态聚合为例。S3900:8台堆叠，分别选取G1/0/10~G8/0/10共8个端口与设备进行聚合对接。配置不用多说了吧。1、创建聚合组: Router(config)#interface port-channel 1002、配置聚合组端口为switchport:Router(config-if)#switchport3、将各端口加入聚合组中:Router(config)#interface range fastEthernet 3/25 -32Router(config-if-range)#switchportRouter(config-if-range)#channel-group 100 mode active &------如果配置手工聚合，该参数选择 on(替换active)OK了，没有别的配置了。
答案创立者
以企业身份回答&
快速解决你的电商难题
店铺优化排查提升2倍流量
擅长&nbsp 店铺优化
您可能有同感的问题}